this post was submitted on 23 Nov 2023
6 points (100.0% liked)

Homelab

22 readers
1 users here now

Rules

founded 1 year ago
MODERATORS
 

This project would never end and I will never get to share it! So here we go πŸ˜‰ I got three switches. Two from ubiquiti(aggregate & 500w POE 48port) and one 100g mikrotik switch. Running most of my servers on 25G and primary nas/server on 100G. I even ran a fiber to my desktop for that sweet 25G laser bits. I got 4 servers. All running V4 Xeon with different levels of horse power. Two dedicated Pfsense boxes on redundant configuration. I use Proxmox as my hypervisor, then I run truenas, k3s on top of it. All of this consumes about 700w. I know it's alot and main server consumes half of it. POE switch takes 100w. Other three servers and the pfsense only consumes 300w. My next project going to getting rid of the monster but I need ton of PCI and 12bays for drive πŸ’Έ. Maybe I'll invest on solar instead πŸ˜…. Feel free to ask any questions.

top 12 comments
sorted by: hot top controversial new old
[–] GoryRamsy@alien.top 1 points 11 months ago

Just saw your post on Lemmy as well

[–] richyrichking@alien.top 1 points 11 months ago (1 children)

How’s the Mikrotik 100G switch? It got an alright review from ServeTheHome from memory. Do you get anywhere near pushing that bandwidth or it’s more for fun? Which I totally get by the way… 😝

[–] hansaya@alien.top 1 points 11 months ago

I can saturate with iperf easily. Otherwise, 20G max in real life because of single thread performance issues

[–] -MO5-@alien.top 1 points 11 months ago (1 children)

Nice setup! I have that same gigabyte server. Mine has a datto d1541 board that I flashed back to asrock firmware. The server as a whole, I like. It's low power consumption but damn those fans scream.

[–] hansaya@alien.top 1 points 11 months ago

Yep, those datto are nice and cheap. I did the same, flashed asrock firmware, and I unplugged some fans in them. Never got too hot and very efficient!

[–] data123456789@alien.top 1 points 11 months ago (1 children)

Is that a simplex keystone in port 2 on the second panel? Never seen anything like that before. If it is, is it preterm or how is the splice housed?

I could be completely wrong πŸ˜‚

[–] hansaya@alien.top 1 points 11 months ago

It's an LC to LC keystone. Behind the keystone, I have plugged into an outdoor rated pre made single mode fiber. That wraps around my house outside to my second floor. Why? I already had a bundle of wires going around the house, so I just made it worse by adding another 😁

[–] shadowtheimpure@alien.top 1 points 11 months ago

I've got one box. Just one. It's built in a Node 804 case with 8 18TB hard drives, an HBA, an RTX 3080, and a Ryzen 3900XT with 64GB of RAM. I've sunk well over $2000 into this one box.

It runs my full media suite (Emby, the *arr suite of software, Jellyseerr for request intake and management) and a little left over for when I feel like spinning up a Minecraft server or something

[–] TheFluffyDovah@alien.top 1 points 11 months ago (1 children)

What's going on with that wall behind the rack? Is that mould?

[–] hansaya@alien.top 1 points 11 months ago

No, just concrete in the basement

[–] cjmute1@alien.top 1 points 11 months ago (1 children)

Is it me or does the top stack look off by a notch or 2?

[–] hansaya@alien.top 1 points 11 months ago

Top server is off by one. Done it to give some ventilation since as you can see I have more than enough space in my rack!