minimalfootprint

I finally have the budget to build my first NAS and upgrade my desktop PC. I have used Linux for quite some time, but am far from an expert.

One of the steps is to move my M.2 NVME system drive (1TB) from my desktop to my NAS. I want to replace it with a bigger NVME drive (2TB). My current motherboard only has a single M.2 slot, that's why I bought a M.2 enclosure.

My goal is to put my new drive into the enclosure, clone my whole system disk onto it and then replace the old drive. At first I found several posts about using clonezilla to clone the whole drive, but some posts mentioned it not working well with btrfs (/ and /home subvolume), which is the bulk of my drive.

I have some ideas how I might to pull it off. My preliminary idea is:

1. clone my boot partition with clonezilla
2. use btrfs-clone or moving my butter to transfer the btrfs partition
3. resize the partitions with gparted (and add swap?)

The two aspects I'm uncertain about are:

1. UUIDs
2. fstab

I plan to replace the old drive, so the system will not have two drives with the same UUID. If the method results in a new UUID I need to edit fstab.

As you can see I'm not sure how to proceed. Maybe I can just use clonezilla or dd to clone my whole drive? If someone has experience with such a switch or is just a lot for familiar with the procedures, I would love some tips and insight.

Thanks for reading.

////////////////////////////////////////////////////////////////////////////////////////////////////////////

EDIT: Thinking about how to do it, might have actually taken longer than the procedure itself. For anyone in a similar situation, I was able to replace the drive with these steps:

1. clone the whole drive (new drive has a bigger capacity) with clonezilla
2. physically switch the drives
3. boot into a live medium and resized the btrfs partition on the new drive with gparted
4. boot into the main system and adjust the filesystem size with sudo btrfs filesystem resize max /

With two NVME drives (even though one was in a USB M.2 enclosure) everything took about 30 minutes. About 300 gigs of data were transferred. I haven't found any problems with the btrfs partition thus far. Using dd like others recommended might work as well, but I didn't try that option.

Until recently I stored my media library in folders. A tedious way to manage a collection.

I set up Jellyfin on my main machine as a test. I enjoy the experience and want to migrate to a NAS, for better reachability in my network. I am a beginner when it comes to networks.

I currently use a single 20TB HDD (current usage 80%) and another 4TB HDD is around somewhere. I was wondering what my options and recommended solutions are. Should I get 1, 2, or more 20TB drives? I want some redundancy, but don't want to invest into too many drives.

Looking forward to any tips or resources to read up on. Thanks.

Thus far I have been playing on my XBox 360 wireless controller, but the rubber has worn off one of the sticks so far, i can feel the edge of the hard plastic beneath it when I play. The springs in the triggers are creaking as well.

So I am looking for a replacement.

Some people recommended the 8BitDo controllers. The 8BitDo Ultimate 2.4 Ghz Controller offers hall effect sensors and a loading dock for the same price as a regular Xbox or Playstation controller.

I found some posts about the compatibility with Linux. The BT+2.4 version seems to have more problems, but even the 2.4Ghz version needs some tinkering.

Does anyone have any experience with 8BitDo in general or the 2.4Ghz model in particular? Are there other controllers I should look at? I mostly play rogue likes with controller and would like a XBox/Playstation style controller.

Thanks.

Edit: Thanks for all the replies and suggestions. I used them and watched some reviews. I went from the 8BitDo Ultimate 2.4Ghz to the GuliKit KK 3 Max and finally landed at the Flydigi Vader 3 Pro. Ordered it from Aliexpress (not available at Amazon in Europe) for under 50€.

Today I was contacted by someone at work. She graduated school with me and our 20 year reunion was coming up. Why did she contact me at work? It was the only way they were able to track me down. I was included in promotional material by name. She told me I "was the hardest to track down"and I had to smile.

This is just a small anecdote about privacy practices and their real life impact (and how your employer can undo all of it, I guess)

Since a recent update I have trouble with my audio devices.

Arch, KDE Plasma 6, X11 I mainly use a USB DAC, but sometimes switch to my TVs speakers (connected via HDMI) and that's where I have trouble with.

The problem is the output profile for my TV is not consistent between reboots of my system and/or TV and has to be manually set. The profile is shown in the Plasma sound settings as inactive.

In this instance the pactl list cards shows the first profile hdmi-stereo as active (available: yes). However I can't switch to it in the Plasma sound settings.

off: Off (sinks: 0, sources: 0, priority: 0, available: yes)
output:hdmi-stereo: Digital Stereo (HDMI) Output (sinks: 1, sources: 0, priority: 5900, available: yes)
output:hdmi-stereo-extra1: Digital Stereo (HDMI 2) Output (sinks: 1, sources: 0, priority: 5700, available: no)
output:hdmi-stereo-extra2: Digital Stereo (HDMI 3) Output (sinks: 1, sources: 0, priority: 5700, available: no)
output:hdmi-stereo-extra3: Digital Stereo (HDMI 4) Output (sinks: 1, sources: 0, priority: 5700, available: no)

So far the active profiles were hdmi-stereo and hdmi-stereo-extra2.

I have to manually activate the profile with pactl set-card-profile alsa_card.pci-0000_26_00.1 output:hdmi-stereo, if the profile has switched. If I try to switch to any of the other stereo profiles, nothing happens, I have to chose the available one.

I didn't have any luck figuring out why the profile can change when I reboot and how I can activate one profile automatically without manual input.

Any help or advice would be appreciated. Thanks for reading.

The whole output from pactl list cards:

Card #47
	Name: alsa_card.pci-0000_26_00.1
	Driver: alsa
	Owner Module: n/a
	Properties:
		api.acp.auto-port = "false"
		api.alsa.card = "0"
		api.alsa.card.longname = "HDA NVidia at 0xfc080000 irq 75"
		api.alsa.card.name = "HDA NVidia"
		api.alsa.path = "hw:0"
		api.alsa.use-acp = "true"
		api.dbus.ReserveDevice1 = "Audio0"
		api.dbus.ReserveDevice1.Priority = "-20"
		device.api = "alsa"
		device.bus = "pci"
		device.bus_path = "pci-0000:26:00.1"
		device.description = "TU106 High Definition Audio Controller"
		device.enum.api = "udev"
		device.icon_name = "audio-card-analog-pci"
		device.name = "alsa_card.pci-0000_26_00.1"
		device.nick = "HDA NVidia"
		device.plugged.usec = "6240124"
		device.product.id = "0x10f9"
		device.product.name = "TU106 High Definition Audio Controller"
		device.subsystem = "sound"
		sysfs.path = "/devices/pci0000:00/0000:00:03.1/0000:26:00.1/sound/card0"
		device.vendor.id = "0x10de"
		device.vendor.name = "NVIDIA Corporation"
		media.class = "Audio/Device"
		factory.id = "14"
		client.id = "45"
		object.id = "47"
		object.serial = "47"
		object.path = "alsa:pcm:0"
		alsa.card = "0"
		alsa.card_name = "HDA NVidia"
		alsa.long_card_name = "HDA NVidia at 0xfc080000 irq 75"
		alsa.driver_name = "snd_hda_intel"
		device.string = "0"
	Profiles:
		off: Off (sinks: 0, sources: 0, priority: 0, available: yes)
		output:hdmi-stereo: Digital Stereo (HDMI) Output (sinks: 1, sources: 0, priority: 5900, available: yes)
		output:hdmi-stereo-extra1: Digital Stereo (HDMI 2) Output (sinks: 1, sources: 0, priority: 5700, available: no)
		output:hdmi-stereo-extra2: Digital Stereo (HDMI 3) Output (sinks: 1, sources: 0, priority: 5700, available: no)
		output:hdmi-stereo-extra3: Digital Stereo (HDMI 4) Output (sinks: 1, sources: 0, priority: 5700, available: no)
		output:hdmi-surround: Digital Surround 5.1 (HDMI) Output (sinks: 1, sources: 0, priority: 800, available: yes)
		output:hdmi-surround71: Digital Surround 7.1 (HDMI) Output (sinks: 1, sources: 0, priority: 800, available: yes)
		output:hdmi-surround-extra3: Digital Surround 5.1 (HDMI 4) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-surround71-extra3: Digital Surround 7.1 (HDMI 4) Output (sinks: 1, sources: 0, priority: 600, available: no)
		pro-audio: Pro Audio (sinks: 4, sources: 0, priority: 1, available: yes)
	Active Profile: output:hdmi-stereo
	Ports:
		hdmi-output-0: HDMI / DisplayPort (type: HDMI, priority: 5900, latency offset: 0 usec, availability group: Legacy 1, available)
			Properties:
				port.type = "hdmi"
				port.availability-group = "Legacy 1"
				device.icon_name = "video-display"
				card.profile.port = "0"
				device.product.name = "SAMSUNG
     "
			Part of profile(s): output:hdmi-stereo, output:hdmi-surround, output:hdmi-surround71
		hdmi-output-1: HDMI / DisplayPort 2 (type: HDMI, priority: 5800, latency offset: 0 usec, availability group: Legacy 2, not available)
			Properties:
				port.type = "hdmi"
				port.availability-group = "Legacy 2"
				device.icon_name = "video-display"
				card.profile.port = "1"
			Part of profile(s): output:hdmi-stereo-extra1
		hdmi-output-2: HDMI / DisplayPort 3 (type: HDMI, priority: 5700, latency offset: 0 usec, availability group: Legacy 3, not available)
			Properties:
				port.type = "hdmi"
				port.availability-group = "Legacy 3"
				device.icon_name = "video-display"
				card.profile.port = "2"
			Part of profile(s): output:hdmi-stereo-extra2
		hdmi-output-3: HDMI / DisplayPort 4 (type: HDMI, priority: 5600, latency offset: 0 usec, availability group: Legacy 4, not available)
			Properties:
				port.type = "hdmi"
				port.availability-group = "Legacy 4"
				device.icon_name = "video-display"
				card.profile.port = "3"
			Part of profile(s): output:hdmi-stereo-extra3, output:hdmi-surround-extra3, output:hdmi-surround71-extra3

Hello sailors,

I wanted to try out Arr* and installed and configured everything for the first few days (Native, Arch). Just tinkering around.

Radarr and Sonarr used qbittorrent at first, but the permissions gave me trouble. I installed qbittorrent-nox and run it via systemd for a different user. This fixed my permission troubles.

However, even though both run with the same settings, nox is firewalled (DHT: 0 nodes, stuck on getting the metadata) while the regular version shows online and downloads with good speeds.

I use MullvadVPN (doesn't offer Port Forwarding anymore). I opened a port in my router.

I'm pretty new to this. Does anyone have any idea what could be the problem? Do I have to add something to the systemd service?

Any hints wouldbe appreciated! Thanks for reading!

systemd service:

[Unit]
Description=qBittorrent-nox service
Documentation=man:qbittorrent-nox(1)
Wants=network-online.target
After=network-online.target nss-lookup.target

[Service]
Type=exec
User=qbittorrent-nox
group=arr
ExecStart=/usr/bin/qbittorrent-nox -webui-port=8080

[Install]
WantedBy=multi-user.target

My current setup includes two 1440p monitors and a 4K TV . In the evening I use a script to switch off the monitors and use the TV. Due to the different resolutions, scaling is a problem. Both X11 and Wayland have their own problems.

My setup: Arch, KDE, Nvidia RTX 2060 with proprietary NVIDIA drivers (edit: version 545.29.06), 2x 1440p 144Hz monitors (DP-0, DP-1), 1x 4K 60Hz TV via (HDMI-0)

X11: Currently my procedure is as follows when I want to switch from monitors to my TV:

1. I turn the TV on
2. I change the Global scale to 175% via the KDE GUI. (I haven't found a command to implement in a script yet)
3. I use xrandr to switch to the TV only. xrandr --output HDMI-0 --primary --mode 3840x2160 --pos 5120x0 --rotate normal --rate 60 --output DP-0 --off --output DP-1 --off

The monitors turn off, but the TV shows a black screen. After a restart the TV works and the scaling is correct. So far I haven't found a way to change the scaling and switch to the TV without a restart.

Oddly if I turn on all screens at the same time, it works. All of them show the desktop xrandr --output HDMI-0 --mode 3840x2160 --pos 5120x0 --rotate normal --rate 60 --output DP-0 --primary --mode 2560x1440 --pos 0x1124 --rotate normal --output DP-1 --off --output DP-2 --mode 2560x1440 --pos 2560x1124 --rotate normal However, when I use step 3 afterwards, the TV shows a black screen again.

I tried to find solutions, but it's hard to figure out, since I'm not sure if it's a driver problem, KDE problem, ...

Wayland:

• the max refresh rate for the TV is 30 Hz
• with the TV turned on the system freezes every few seconds for a second or two

I haven't tinkered with Wayland a lot. The freezes make it a no-go for now. X11 at least has a workaround, even though it's a bit annoying.

Even though I have used Linux for a while. I'm probably still considered a beginner, so any help would be appreciated.